BIG Kaiser Higher Precision Guaranteed
View the site en Espaņol
Search the site:
 
Products >> Accessories >> Chip & Coolant Fans

Chip & coolant Fans

Chip Fan

Clean-Tec chip & coolant fans provide a safer and faster method of removing chips and coolant from your tables, fixtures and workpieces than conventional air. The Clean-Tec chip & coolant fan can be programmed into your machining cycle to help reduce downtime and make necessary cleaning a part of the work cycle.

 

Clean-Tec CHIP & coolant FAN Flv


Chip Fan in action

As the machine spindle turns, the blades deploy to provide high volume air cleaning power!

  • In-process cleaning without stopping production
  • Saves expensive compressed air
  • No more dripping coolant and flying chips from conventional air hose blasts
  • Less spindle downtime
    for cleaning results in
    increased profits
  • A quieter workplace environment
  • Coolant-through shank for rinsing capability

A Variety of Clean-Tec Chip & Coolant Fans

Chip Fan Model 160

Clean-Tec Chip & Coolant Fan Model 160


Available in metric and inch sizes.

  • Capable of 6,000 to 12,000 RPM with coolant.
  • Rinse with coolant and blow even narrow spaces & milling pockets clean with small diameter rotor blades (160mm).
  • For revolutions of 6,000 to 12,000 RPM (max) with coolant channel, clockwise rotation.

Chip Fan Model 260

Clean-Tec Chip & Coolant Fan Model 260


Available in metric and inch sizes.

  • Capable of 5,000 to 8,000 RPM.
  • Used for quick and efficient blowing of work surfaces & machined pieces.
  • For revolutions of 5,000 to 8,000 RPM (max), clockwise rotation.
  • Full blowing of workpieces and work surfaces quickly
    and efficiently.
  • Rotor blade diameter 260mm

Chip Fan Model 330

Clean-Tec Chip & Coolant Fan Model 330


Available in metric and inch sizes.

  • Capable of 5,000 to 8,000 RPM.
  • Used for quick and efficient blowing of work surfaces & machined pieces.
  • for revolutions of 5,000 to 8,000 RPM (max), clockwise rotation.
  • Full blowing of workpieces and work surfaces quickly
    and efficiently.
  • Rotor blade diameter 330mm

coolant through capability

Chip Fan cleaning a workpiece

may be used in all horizontal and vertical machining centers

Clean-Tec Chip & Coolant Fan demonstrating through coolant capability.

A closer view of the same Chip Fan cleaning the workpiece.

The Clean-Tec Chip & Coolant Fan may be used in all horizontal and vertical machining centers by using a normal chuck with a clamping diameter of 20mm or 3/4".


Repair Kits

4 rotor-blades*, springs, screws and pins.
*Blades will wear with normal use and may require replacement. Maintain & replace as needed.

For Model 160: Part # 24.303.206

For Model 260: Part # 24.303.207

For Model 330: Part # 24.303.205

Replacement Springs (10/pack): Part # 24.303.210



PRECAUTIONS:

Clean-Tec Chip & Coolant Fan are to be used in enclosed machining centers only!

Rotation of the fans is to be clockwise only!

Follow instructions, do not exceed specified RPMs!

All operators/users of this product should be informed of and must read these instructions. Clean-Tec Fans can ONLY be used in ENCLOSED MACHINING CENTERS! Clean-Tec Fans equipped with either a 0.75" O.D. or 20mm straight shank should be securely mounted in either a collet chuck or end mill holder. Rotational direction clockwise only. Optimum feed rate for cleaning is between 120-390 in/min. Distance from workpiece should be between 4"-6" Upon rotational start-up, program an initial speed of 2,000 RPM (max) before obtaining running speed to reduce the possibility of blade failure due to excessive centrifugal force.